The 870 Series Contactor Temperature Control panel is ON/OFF process temperature control and is recommended for applications that do not demand precise temperature control.
-
250° Construction Process Air Heater
With a robust construction the Tubular Process Air Heater can be used in most applications where moisture and particulates are present in the air stream.
-
310 Series Thermistor Sensors
The 310 series thermistor sensors must be wired in series with a 320 series setpoint adjuster. The total resistance is 2200 ohms when the sensor temperature equals the setpoint. The NTC thermistor increases resistance as temperature decreases.
-
320 Series Setpoint Adjusters
The 320 series Setpoint Adjuster must be wired in series with a 310 Series Thermistor sensor. The total resistance is 2200 ohms when the sensor temperature equals the setpoint. The 205-S10 Series step controller uses a version of the 320 Series Setpoint Adjuster.
-
870 Series SCR Control Panel
The 870 Series SCR Control panel is a fully proportional process temperature control panel that utilizes SCR Power Controllers to modulate the entire heater load directly, varying the heater output from 0 to 100% of the total heater KW.
-
873 Series Quick Ship Contactor Control Panel
The Quick Ship Contactor Temperature Control panel provides fast shipment, compact packaging, and is pre-engineered for resistive load applications. The panel is completely assembled, pre-wired, tested, and ready for trouble free installation and operation.
-
873 Series Quick Ship SCR Control Panel
The Quick Ship SCR Temperature Control panel provides fast shipment, precise temperature control, compact packaging, and is pre-engineered for resistive load applications. The panel is completely assembled, pre-wired, tested, and ready for trouble free installation and operation.
-
A Series and B Series Power Controllers (Series 101, 102, 103, & 108 )
Series 101, 102, 103, & 108 available as Model A & B power controllers are solid state, zero-cross fired, proportional devices. Line voltage is switched 0 – 100% linearly, with respect to the input range, and a 1 second time-base controls power to the load. Current ratings up to 50 amps and various configurations available for indoor and outdoor construction.
-
Circulation & In-Line Heaters
Indeeco circulation heaters are used to maintain, raise, preheat and boost process temperatures from -50° F to 1200° F for a wide variety of liquids and gases found in commercial, industrial and military applications.
-
Compact Explosion-proof Unit Heater
Compact and cost-effective, Indeeco’s explosion-proof unit heater is ideal for small hazardous areas needing safe, space-saving heat solutions.
-
Component Heating Elements
Indeeco offers many types of component heaters to the Marine Industry as well as replacement heating elements for Indeeco duct type heaters. These components are unique to Marine application as they are designed and fabricated in-house to meet your needs.
-
Cooling Tower Heaters
Indeeco offers American made cooling tower heaters that available with copper elements and brass fitting or stainless steel elements with stainless steel fitting. All heaters include a cast NEMA 4 terminal enclosure.
-
Cooling Tower Panels
Indeeco Cooling Tower Control Panels offer a lower installation cost by reducing individually mounted temperature and liquid level control devices with one pre-engineered and assembled control package.
-
Compressor Heater
Our CMPHTR Compressor Heater is a cutting-edge solution designed to safeguard your compressors and ensure optimal performance even in the harshest conditions.
-
CRG®
CRG® Heating Cables are designed for freeze protection of metal and plastic pipes as well as roof & gutter de-icing applications. 150°F Maintain, 185°F Exposure, 120-277V operation, (3,5,8,10 w/ft) FM, CSA, UL.
-
Custom Designed Process Air Heaters
Indeeco has the expertise to design and customize heaters for unique, challenging, or highly specialized applications, ensuring optimal performance in even the most demanding environments.
-
Electronic Controls
Heat Trace controls and monitoring systems are available in: Single, Dual, and Multi Loop configurations for line and ambient sensing applications in ordinary and hazardous areas. These systems are designed and manufactured to insure your Heat Trace system reliability and integrity. Whether it is stock product or a custom solution provided from our UL-508 approved panel shop, we have you covered.
-
Explosion-Proof Flanged Immersion Heaters
Commonly used in the refinery and petrochemical industries, Indeeco explosion-proof flanged immersion heaters provide a reliable solution for heating tanks, pressure vessels, and in-line processes.
-
Explosion-Proof Screw Plug Immersion Heaters
Indeeco explosion-proof screw plug immersion heaters are CSA approved, for use in hazardous areas classified as Class I, Division 1, Groups B, C and D; and Class II, Division 1, Groups E, F and G.
-
HX Series Enclosure Heaters
Indeeco HX Series Enclosure Heaters offer compact, reliable heating for electrical enclosures—easy to install as a direct replacement for strip heaters.
-
Field Upgrade Enclosure Heater
Indeeco Field Upgrade Heating Units offer the same basic design as the Indeeco HX Series Enclosure Heater with the benefit of expanded voltage ranges for connecting directly to incoming power feeds.
-
Flexible Bolt Heaters
Indeeco Flexible Bolt Heaters are specifically designed to provide easy access to stud bolts in applications with limited overhead clearance. Built on a time-proven design, these heaters deliver 50 watts of heat per square inch, ensuring fast and efficient performance. The flexible sheath can be bent or shaped to nearly any required configuration, making installation simple—even in the most challenging spaces.
-
Fluid Heating Equipment
With complete in-house facilities to manufacture pressure vessels, immersion heaters, sheet metal enclosures and electronic controls, Indeeco offers a complete line of heater-control packages for water, oil, and other fluids.
-
HSR® – Self Regulating Cable
HSR® Heating Cables are designed for freeze protection and temperature maintenance of metal pipes and tanks. 375°F Maintain, 450°F Exposure, 120-277V operation (20,25,30 w/ft) FM, CSA, CE
-
Impedance Pipe Heating Systems
Indeeco Impedance Heating Systems are unique, safe and a proven method for electric pipeline tracing and heating. The pipe actually becomes the heating element when low AC voltage is applied to it by a special, custom designed transformer.
-
LSR®
LSR® Heating Cables are designed for freeze protection and temperature maintenance of metal and plastic pipes. 150°F Maintain, 185°F Exposure, 120-277V operation, (3,5,8,10 w/ft) FM, CSA, UL, CE
-
M & S Series Power Controllers
Model M & S Series power controllers are solid-state, zero-cross fired, proportional devices. Line voltage is switched 0-100% linearly, with respect to the input range, and a 4 second time-base controls power to the load. Capable of pairing with Indeeco sequencers for full vernier control, Type 4X construction when properly optioned, and rated up to 70 amps for diverse applications.
-
Mineral Insulated Cables
Mineral Insulated cables and accessories are available for maintain temperatures to 900°F (482°C), exposure temperatures to 1100°F (593°C), operating voltages from 120 to 600 volts, and power output up to 50 watts per foot.
-
MSR®
MSR® Heating Cables are designed for freeze protection and temperature maintenance of metal pipes and tanks. 250°F Maintain, 366°F Exposure, 120-277V operation (5,10,15 w/ft) FM, CSA, UL, CE
-
Non-Hazardous Flanged Immersion Heaters
Indeeco flanged immersion heaters are among the most widely used solutions for heating fluids and gases. Designed for tanks, pressure vessels, and in-line heating, these flange heaters offer easy installation and low-maintenance operation.
-
Open Coil Process Air Heaters
Ideal for clean dry air applications Indeeco’s Open Coil Process Air Heaters offer precise heat at an economical price.
-
Over-the-Side Heaters
Indeeco Over-the-Side heaters are designed to provide the maximum in application flexibility and to minimize installation cost. They are ideal for jobs where easy installation and quick replacement or cleaning must be accomplished without emptying the tank.
-
Process Skid Heating
When providing electric heaters for skid-mounted process systems, the critical needs are custom design capabilities and the flexibility to deliver under time constraints. Indeeco is an industry leader in meeting those tests.
-
Rectangular Flange Heaters
Indeeco rectangular flange heaters are designed to provide efficient, uniform heating for tanks, vessels, and process equipment. Their robust construction and easy-to-install flange design ensure reliable performance and simplified maintenance. Available in various sizes and materials, these heaters can be customized to meet your specific application requirements.
-
Refrigeration Defrost Heaters
Electric defrosting of coils and evaporator pans for commercial refrigeration equipment. May be clamped to pipes or tanks to promote drainage and prevent freezing.
-
Replacement Boiler Flange Heaters
These 4-7/8” flange heaters are three-element modules specifically designed for large steam or hot water boilers. They offer a simple, practical solution to two problems inherent in all electric boiler designs: element stocking and field replacement.
-
S10 Series Step Control
Indeeco S10 series step controller does more to provide precision control for multi-stage applications.
-
S5 Series Step Control
Indeeco’s S5 Series step controller provides low cost precision control for multi-stage applications.
-
Screw Plug Immersion Heaters
Indeeco screw plug immersion heaters are ideal for use in direct heating of liquids and gases in a variety of processes for hazardous and non-hazardous locations. Indeeco offers customized wattages with voltages up to 600V and are available in 1″, 1-1/4″, 2″, 2-1/2″, and 3″ NPT sizes. You can order from stock or customize for your specific application.
-
Marine Sloped Top Convector
Indeeco Commercial Marine Sloped Top Convectors are available with the same electrical ratings and physical dimensions as their Mil-Spec counterparts and may also be provided with complete built-in controls to allow for a single point electrical connection.
-
Standard Bolt Heaters
Indeeco Bolt Heaters are designed to preheat large, hollow holding bolts or studs where rapid, concentrated heat is essential for thermal expansion. These insertion-type heaters are ideal for applications that demand quick and uniform heating, making them a go-to solution for the manufacturing and servicing of heavy-duty steam equipment, turbines, and other high-pressure systems. Their efficient performance helps reduce downtime and ensures secure, reliable bolt tensioning.
-
Tank and Basin Heaters
Indeeco Tank Heaters are used to maintain or raise the temperature of gases and fluids in tanks from -300°F to 1000°F for a variety of applications and industries. These heaters are designed with low watt density, open coil heating elements for uniform heating of even the most temperature sensitive materials.
-
Bottom-Mounted Immersion Heaters
Bottom-Mounted immersion heaters were originally designed for use in coffee urns. However, their compact construction makes them ideal for use in steam tables, humidifiers, sterilizers and other applications requiring a very low heater profile and a short element length.
-
Tank Heating
Indeeco Electric Storage Tank Heaters are used to maintain or raise the temperature of gases and fluids in tanks from -300°F to 1000°F for a variety of applications and industries.
-
Thermostat Controls
Mechanical thermostats are designed for ordinary and hazardous area use. Manufactured for high accuracy, single pole double throw contacts, 22 amps, 120 to 480 volt operation and ambient or line sensing. Available from stock for same-day shipment.
-
Triad Washdown/Corrosion Resistant Unit Heater
The Indeeco Triad stainless steel construction with non-metallic NEMA 4X enclosure can be hosed down for cleaning in dirty, wet and corrosive marine applications. Triad unit heaters are UL listed, File #E97759(n), meet U.S. Coast Guard requirements and are ABS approved.
-
Tubular & Finned Tubular Elements
Our product offering ranges from standard tubular heating elements to the most sophisticated, custom designed systems. Indeeco’s attention to detail and rigorous testing give worldwide customers premium products that they receive quickly and at a fair price.
-
Tubular Process Air Heaters
With a robust construction the Tubular Process Air Heater can be used in most applications where moisture and particulates are present in the air stream.
-
Type T Convector
The Type T (turrett) construction per MIL-H-22663 has no built-in controls. The new Navy design, per NAVSEA document #59512-BS-MMA-010 includes both a built-in manual reset over temperature cutout and a thermostat. Heaters are also available with a complete built-in control package to eliminate the need for remote contactors and transformers.
-
Vent Duct Heaters
As long time leaders in this field, we fabricate all essential components …right through to final assembly and testing. We make our own finned tubular elements, weld and fabricate the sheet metal frames, and manufacture the electronic controls.